E14某研发楼结构设计

 2023-03-22 10:03

论文总字数:132661字

摘 要

本毕业设计题目是“E14某研发楼结构设计”。该研发楼的建筑总高度为13.2米,共四层,底层层高3.3米,其他层层高均为3.3米,总建筑面积为3300平方米。本建筑采用钢筋混凝土现浇框架结构体系,基础采用独立基础,抗震设防烈度为度,设计基本地震加速度值为,场地土类别为Ⅱ类,设计地震分组为Ⅰ组。

本设计主要是进行框架结构设计,内容包括结构计算和施工图绘制两部分。其中结构计算包括电算、手算和两种算法结果的对比分析。电算内容包括:先用 PMCAD进行建模,输入荷载,再用 SAT-8进行框架的空间结构内力分析和计算及配筋计算,最后用 PKPM 软件输出标准层楼面梁平面配筋图、屋面梁平面配筋图、标准层楼板配筋图、屋面板配筋图、框架柱平面配筋图、详图等施工图。

手算内容包括:确定结构体系及构件尺寸,进行结构平面布置,楼板设计,计算横向框架在竖向荷载作用下的内力,计算横向框架在风荷载作用下的内力,计算横向框架在水平地震作用下的内力和位移,并且进行框架梁柱内力组合、结构构件截面设计、楼梯设计和基础设计。画出楼梯结构图、基础平面布置图及基础详图。

最后再进行手算和电算两种结果的对比分析。施工图共十张,包括:结构施工设计总说明,基础平面布置图及基础施工详图,柱平法施工图,三层楼面板平面整体配筋图及楼面梁平面整体配筋图,顶层屋面板平面整体配筋图及屋面梁平面整体配筋图,一二层楼面板平面整体配筋图及楼面梁平面整体配筋图图,楼梯结构施工图。

关键词:结构设计;钢筋混凝土;框架结构;内力计算

The Structural Design E14 of Ramp;D Building

Abstract

The graduation project is “the structural design E14 of Ramp;D Buinding”. It is a four-floor building and the overall height of the building is 13.2 meters.The bottom storey is 3.3 meters and the other storeys are 3.3meters.The teaching building"s total construction area is 3300 square meters. The building is cast reinforced concrete frame system, based on independent foundation.The seismic intensity is 7 degrees, the basic design earthquake acceleration is 0.15g, site soil category is group Ⅱ and design earthquake is group I.

The design is primarily for frame design, including structural calculations and construction drawings of two parts.Structure calculations include computing, hand calculation and comparing the results of two algorithms.Computing includes: make a model with PMCAD, input load firstly, then use SAT - 8 to computate the internal forces of spatial structure and reinforcement, finally output of the standard layer of floor beam reinforcement plans, the roof layer of floor beam reinforcement plans,standard floor slab reinforcement plans, roof reinforcement plans, frame column reinforcement drawings and other construction plans with PKPM software.

Hand calculation include: determine the size of structural systems and components, the structure layout, floor design, horizontal frame under vertical load calculation diagram and force calculation, horizontal frame under wind load calculation diagram and the force calculation, horizontal frame under horizontal earthquake calculation of internal forces and displacements, internal force combination beam frame, frame beam and column design, stair design and basic design. And draw stair structural reinforcement plan ,basic floor plan and the basis detailing plan.

Finally, the two results are during the hand count and computing comparative analysis. A total of eight working drawings, including: the general information of the structure construction design, the basic floor plan and foundation construction plans, the column flat construction plans, the standard layer of floor beam and slab reinforcement plans, the roof layer of floor beam and slab reinforcement plans, the structure floor plans and the staircase structure construction plans.

Keywords: Structural Design; Reinforced Concrete;Frame Structures;Calculation of Internal Force

目 录

摘 要 I

Abstract II

目 录 III

1.1 课题背景与意义 1

1.2 课题研究方案 1

第二章 工程概况和设计资料 2

2.1 工程名称 2

2.2 工程概况 2

2.3 设计资料 2

2.3.1 工程地质资料 2

2.3.2 气候条件 2

2.3.5 其他 3

第三章 结构的平面布置 3

3.1 结构的平面布置图 5

3.2.1框架梁的尺寸截面初估 6

3.2.2框架柱的尺寸截面初估 7

第四章 楼板荷载及板厚的计算 9

4.1楼板荷载的传递分布 9

4.2楼板荷载 10

4.2.1 恒荷载 10

4.2.2 活荷载 11

4.2.3 梁间荷载 11

4.3 板厚的确定 12

第五章 横向框架在竖向荷载作用下的计算简图及内力计算 13

5.1 横向框架在恒荷载作用下的计算简图 13

5.1.1 横向框架的简图 13

5.1.2 底层的框架计算简图 13

5.1.3 第二层的框架计算简图 19

5.1.4第三层框架的计算简图 22

5.1.5顶层框架的计算简图 24

5.1.6 恒荷载作用下的横向框架的计算简图 28

5.2 横向框架在活载作用下的计算简图 29

5.2.1 底层框架的计算简图 29

5.2.2 第二、三层框架的计算简图 32

5.2.3 顶层框架的计算简图 32

5.2.4 活荷载作用下的横向框架的计算简图 35

5.3 横向框架在恒荷载作用下的内力计算 35

5.3.1 采用弯矩二次分配法计算弯矩 35

5.3.2 绘制横向框架的内力图 39

5.4 横向框架在活荷载作用下的内力计算 41

5.4.1 运用弯矩二次分配法计算弯矩 41

5.4.2 绘制内力图 42

第六章 横向框架在风荷载作用下的计算简图及内力计算 44

6.1 横向框架在风荷载作用下的计算简图 44

6.1.1 垂直于建筑物表面的风荷载标准值的计算 44

6.1.2 各层楼面处集中风载标准值的计算 45

6.1.3 风荷载作用下的计算简图 45

6.2 横向框架在风荷载作用下的位移计算 45

6.2.1 框架梁柱的线刚度计算 45

6.2.2 侧移刚度D值的计算 46

6.2.3 风荷载作用下框架侧移的计算 47

6.3 横向框架在风荷载作用下的内力计算 47

6.3.1 反弯点高度的计算 47

6.3.2 柱端弯矩及剪力的计算 47

6.3.3 梁端弯矩及剪力的计算 48

6.3.4 柱端剪力的计算 50

6.3.5 柱的轴力计算 50

6.3.6 绘制横向框架的内力图 51

第七章 横向框架在水平地震作用下的内力和位移的计算 53

7.1 重力荷载代表值的计算 53

7.1.1 第四层的重力荷载代表值的计算 53

7.1.2 第三层的重力荷载代表值的计算 54

7.1.3 第二层重力荷载代表值的计算 56

7.1.4 第一层的重力荷载代表值计算 57

7.2 横向框架在水平地震作用下的位移计算 60

7.2.1 框架梁柱的线刚度计算 60

7.2.2 抗侧刚度D的计算 60

7.2.3 结构基本自振周期的计算 60

7.2.4 横向水平地震作用的计算 61

7.3 水平地震作用下横向框架的内力计算 62

7.3.1 反弯点高度的计算 62

7.3.2 柱端弯矩及剪力的计算 63

7.3.3 梁端弯矩及剪力的计算 63

7.3.4 柱端剪力的计算 64

7.3.5 柱的轴力计算 64

7.3.6 绘制内力图 65

第八章 框架梁柱内力组合及截面设计 67

8.1 一般规定 67

8.1.1 梁端的负弯矩调幅 67

8.1.2 选定控制截面 67

8.1.3 荷载效应组合的种类 68

8.2 框架梁的内力组合 68

8.2.1 梁端负弯矩的调幅 68

剩余内容已隐藏,请支付后下载全文,论文总字数:132661字

您需要先支付 80元 才能查看全部内容!立即支付

该课题毕业论文、开题报告、外文翻译、程序设计、图纸设计等资料可联系客服协助查找;